Scythe Susanoo 12 Heatpipe 4 Fan SCSO-1000 CPU Cooler Review

I wasn't sure coolers could get much larger, but Scythe is pushing the limits with the Susanoo.  One advantage of a huge, wide cooler with four fans, is that you get "all over" cooling.  It will cool your RAM, North Bridge, and even your graphics card, although to a smaller degree.

 

Introduction

The Susanoo Scythe CPU cooler consists from the total of twelve 6mm heat pipes and features a two segment heat sink configuration by the name of DBS (Double Block Structure), resulting the Susanoo to this massive top-flow cooler form. Thanks to the large cooling area, the surrounding components such as MOSFETs, Northbridge, RAM and graphics card can be cooled simultaneously.The Scythe with Susanoo CPU Cooler is equipped with FMSB3 (Flip Mount Super Back-Plate 3) to ensure secure mounting on to the motherboard.

 

Features

D.B.S (Double Block Structure)
By splitting the heatsink fin and heatpipe structure into 2 layers, 6 heatpipes at the bottom part + main heatsink fins to absorb the heat as a primarily stage, then the upper 6 heatpipes and sub heatsink fins to absorb the rest of the heat to create the ultimate cooling solution. Total 12 heatpipes are used in this super ultra-sized dimension heatsink, challenging the limit of the top-flow heatsink performance in the market!

 

W.A.M.S (Wide Area Multi Fan System)
All components around the CPU socket, including MOSFET, Northbridge, VGA, as well as RAM, this super ultra-sized heatsink can cool the entire devices in your PC! By using the build-in fan controller, this cooler can meet the demand from silent to high-performance users!

 

F.M.S.B.3 (Flip Mount Super Back-Plate 3)
Improved Scythe original back-plate names F.M.S.B.3 (Flip Mount Super Back-plate 3), the compatibility has been maximized as well as achieving the solid mounting of the cooler onto the motherboard.

 

Specifications

Model Name:
Susanoo CPU Cooler

Model No.:
SCSO-1000

Manufacturer:
Scythe Co., Ltd. Japan

Compatibility:
Intel®:
Sockel T / LGA775
Sockel LGA1155
Sockel LGA1156
Sockel LGA1366

AMD®:
Sockel AM2
Sockel AM2+
Sockel AM3

Dimensions:
210 x 210 x 160 mm / 8.27 x 8.27 x 6.30 in

Weight Included Fan:
1,565 g / 55.20 oz.

Accessory:
Back-Plate, Mounting Screws, Metal Assembly Clips, Pair of Fan Clips, Thermal Grease, Plastic Spacer, Rubber, Installation Guide

Material of Base Plate:
Nickel-plated copper (more information)

 

Fan-Specifications (4pcs.)

Model Name:
Slip Stream 100 mm

Fan Dimensions:
100 x 100 x 25 mm / 3.94 x 3.94 x 0.98 in

Fan Speed:
500 rpm (±30%) ~ 2,000 rpm (±10%)

Noise LEvel:
9.42 ~ 37.69 dBA

Air Flow:
50.05 ~ 200.21 CFM = 85.03 ~ 340.14 m³/h

Voltage Range
12 V

 

Special Considerations

Recommended PC Case/ Using Environment

Due to the dimensions of this CPU Cooler Being Very Large. You may not be able to install this product into your PC case depending on the components installed inside this PC Case. Furthermore, you may require any 3rd party’s assistance as well as non-standard processes to complete the installation. Following shows the minimum requirements to follows, in order to install this product. Before Purchasing this product, please read this notice and the following information carefully.

Mandatory Factors

1.Width of the PC case must be 200mm or above (no side fan or air duct should be installed on the pc case)
2.PC case must have the screw holes for square nut in all positions to install the motherboard (in case of using motherboard spacer-free PC Case, this product cannot be installed)
*Upper and lower part of the motherboard needs to be attached with screws
*PC case must come with the square nut of its height being over 7mm
3.Supplemental power connector of the graphic card must face towards the drive(not facing towards side panel)
4.Only compatible with ATX motherboard with 9 point attachment

Conditional Factors

1.If the supplemental power connector of the graphic card is facing towards the side panel of the PC case, one of the following need to be fulfilled in order to install this product.
-distance between the position of the supplemental power connector and the PCI bracket is more than 25cm
-Expansion slot for the graphics card on the motherboard is not covered by this product.

2.Graphic card with unusual cooling devices attached (such as heatpipe) any interfere with this product. In this case, it is recommended to use the motherboard with the expansion slot not covered by this product.
*even the above factors are fulfilled the product installation is not guaranteed. Out website and forum will provide updates from time to time.

 

You have no rights to post comments